Peinture en aérosol GHIANT Lexan Spray Fluo Yellow n° 1007 150 ml

This ready-to-use, quick-drying, and fuel-resistant Lexan spray paint in fluorescent yellow is specially developed for painting polycarbonate RC car bodies.

The solvent-based formula etches the surface to bond permanently, offering a lightweight finish that can save up to 15 grams on a 1/10 scale race body for a lower center of gravity.

For the best fluorescent effect, the paint should be applied in very light coats at temperatures above 15°C from a distance of +/-15/20 cm and then backed with white RC Car Colour.

• Delivered in a 150ml aerosol can.

Fluorescent yellow spray paint for polycarbonate RC car bodies, 150 ml

Ghiant RC Car Colours Fluo Yellow is a ready-to-use, quick-drying, lightweight, fuel-resistant spray paint for racing, developed for polycarbonate RC car bodies.

Its solvent etches the surface so the paint bonds permanently with the polycarbonate.

Compared with pre-painted or water-based coloured bodies, the paint can reduce the weight of a 1/10 scale race body by up to 15 g, lowering its centre of gravity.

• Specifications
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: IF eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.
• In the box
• 1× 150 ml spray paint

Before painting, remove dirt particles, cut out the body and sand the cut edges.

Mask areas that are not to be painted with masking film or tape; make sure surfaces are dry and free of dust.

Many bodies have a transparent protective foil on the outside. Do not remove it until the paint has dried.

Paint dark colours before light colours to prevent the dark colours from showing through.

Shake the can vigorously for approx. 2 min. before use, until the mixing ball rattles.

• Spray from approx. 20–30 cm using even cross movements.
• Covering capacity varies slightly by colour.

Apply light coats to avoid bleeding; the final result takes 2–3 coats.

Wait approx. 5 min. between coats rather than applying one heavy coat.

Let the paint dry for 5 minutes before removing the masking film and applying the next coat.

After use, turn the can upside down and spray for 2 s until the nozzle is empty.

• Fluorescent colours appear not to cover as well as normal colours.

Apply only very light coats at temperatures above 15 °C, spraying from a distance of +/-15/20 cm.

Let fluorescent colour dry for 30 min., then back it with white RC Car Colour to obtain the fluorescent effect.

RC Car Colours Fluo Yellow is a paint for Lexan car bodies. The solvent dissolves the body surface so that the paint permanently bonds with the plastic. The paint remains elastic, even in a strong crash, and does not chip or scratch.

• Highlights
• Remains elastic
• Permanently bonds with the body
• Fuel resistant
• Technical data
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: IF eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.
• Scope of delivery
• 1× Lexan paint Fluo Yellow, 150 ml
• Notes

Remove any protective film on the outside of the body only after painting; the body can be cut out beforehand.

Clean the body thoroughly with dish soap or brake cleaner and shake the can vigorously for about 2 minutes.

Spray the paint from a distance of 20–30 cm. When using multiple colours, start with the darkest, as dark colours can otherwise show through the light ones.

Apply several thin coats rather than one thick coat and wait about 5 minutes between coats. Wait at least 5 minutes before removing the protective film or masking film of the design.

After use, turn the can upside down and spray for about 2 seconds to empty the nozzle.

Fluorescent colours cover less than standard colours; apply several fine coats. The ambient temperature should be at least 15 °C and the spray distance 15–20 cm.

Wait about 30 minutes and back the fluorescent colour with white to achieve the luminosity of the neon colour.

• Brand: Ghiant